Types of Rudders Used For Ships

0 comments

Types of Rudders Used For Ships

By Soumya Chakraborty | In: Naval Architecture | Last Updated on February 11, 2019

Types of Rudders Used For Ships

Have you ever noticed that ships, unlike most aeroplanes do not have the same kinds of rudders? The type of rudder that would suit a particular ship is a decision that needs to be based on various factors like hull form, speed, propeller design, the structural arrangement of the stern, clearance between the propeller and the stern, and also a few hydrodynamic factors that dictate the flow of water aft of the propeller.

How ship designers go about deciding the type of rudder, is actually an iterative process. In the concept ship design stage, we actually do not (or cannot afford to) decide the suitable rudder for the ship. So what designers and naval architects do is, estimate a very approximate dimension of the rudder along with the propeller. But as we enter the preliminary design of the ship, the rudder and propeller dimensions are almost fixed, giving us an almost clear idea of the type of rudder that would best fit the design problem.

rudder

However, what becomes significantly important from a designer’s point of view, is deciding on the type and location of the rudder, depending on the hull and propeller design.

Let’s try to understand this in a simple way.

The selection of the proper type of rudder is as important as the location of the rudder behind the propeller. The location of the rudder should be such that it is properly oriented within the propeller’s outflow, so as to produce the required turning moment on the ship (Before we go ahead, you might like to read How does a rudder work on a ship?). A slight change in the rudder type, dimension, and position can bring about a huge variation in the ship’s response to the rudder, as well as the turning ability of the ship. So, optimization is the key.

Related Reading:

Understanding the design of ship propeller

Understanding the design of container ships

Understanding the design of oil tankers

Types of Rudders For Ships

To broadly categorize conventional rudders, there are two types of ship rudders:

1. Spade or Balanced Rudder

A spade rudder is basically a rudder plate that is fixed to the rudder stock only at the top of the rudder. In other words, the rudder stock (or the axis of the rudder) doesn’t run down along the span of the rudder. The position of the rudder stock along the chord of the rudder (width meaning, from the forward to aft end of the rudder) actually decides whether the rudder is balanced of semi-balanced one. In balanced rudders, (which spade rudders generally are) the rudder stock is at such a position such that 40% of the rudder area is forward of the stock and the remaining is aft of it.

A genuine question that must have come up in your mind is, why is such a position chosen for the rudder stock? The answer lies in simple physics. The centre of gravity of the rudder will lie somewhere close to 40% of its chord length from its forward end. If the axis of the rudder is placed near to this location, the torque required to rotate the rudder will be much lesser than what is required to move it, had the axis been placed at the forward end of the rudder. So, the energy requirement of the steering gear equipment is reduced, therefore lowering the fuel consumption of the ship.

spade rudder

2. Unbalanced Rudders

These rudders have their stocks attached at the forward most point of their span. Unlike balanced rudders, the rudder stock runs along the chord length of the rudder. The reason is simple. In this case, the torque required to turn the rudder is way higher than what is required for a corresponding balanced rudder. So, the topmost part of the rudder has to be fixed to the spindle so as to prevent it from vertical displacement from its natural position. However, unbalanced rudders are not widely used now.

Having discussed the conventional types of rudders, let us shift into something yet more interesting. Researchers and ship operators had found significant problems with the balanced and unbalanced rudders. That is, in case there was a failure of the steering gear mechanism while turning a ship. The rudder would remain still with its angle of attack in that condition. The solution to this was found in designing an optimized Semi-Balanced Rudder.

unbalanced rudder

a. Semi- Balanced Rudder:

If you have been able to visualize a balanced and unbalanced rudder by now, it should be pretty easy to visualize a semi-balanced rudder. In fact, the rudder you see on most ships are semi-balanced in the modern industry. The name semi-balanced itself implies, that the rudder is partly balanced and partly unbalanced. If you refer to the figure below, you’ll see that a portion of the chord length from the top is unbalanced, and the remaining chord length is balanced. Why? Read on.

The top part being unbalanced will help in acting as structural support to the rudder from vertical displacement. And the balanced part will render less torque in swinging the rudder. As a result, a semi-balanced rudder returns to the centreline orientation on its own if the steering gear equipment fails during a turn.

semi balanced

Note in the above figure the Rudder horn. Semi-balanced rudders are again of two types depending upon the depth of the horn (which affects the response and torque characteristics of the rudder). A shallow horn rudder will have a horn which extends hardly half the chord length of the rudder from the top. Whereas, a deep horn rudder will feature a horn deeply extending up to more than 50 % of its chord length from the top of the rudder.

Apart from these, designers have developed some other, rather unconventional rudder systems, which gets more interesting to look into.

Related Reading:

Understanding the design of ship’s hull

Different technologies to measure hull stresses

b. Flaps Rudder:

You must have watched an aeroplane’s wings closely. Did you watch those flaps coming in and out of the aft end of the wing? Why do you think they do that? Primarily to change the effective angle of attack of the entire aerofoil section of the wing. You’ll see, during a takeoff, how all the flaps are completely deployed. That actually helps in attaining the effective angle of attack so as to get the maximum lift force.

The same principle, when used in rudders, provides a similar result. Just that, in case of rudders, the flaps are not retractable and they have their significant effects when the rudder is given some angle of attack.

flap

c. Pleuger Rudder:

Perhaps one of the most innovative rudder mechanisms you will ever come across. Suppose you have a ship, too large to be manoeuvre in a basin with size constraints, such that the ship cannot use its propeller during the manoeuvre. This situation often arises in case of large ships operating in space-constrained basins, or in any case of low-speed manoeuvres.

So, a Pleuger rudder (as you can see in the figure below), has a smaller auxiliary propeller housed within it (which runs by a motor). As this housing is mounted on the rudder itself, it generates a thrust (which is smaller than what is generated by the ship’s main engine propeller) in a direction that is oriented along the rudder, therefore allowing effective manoeuvre in slow speed condition.

Pleuger Rudder

Such a rudder can be used in normal conditions also. Just that, in normal speeds, the Pleuger is not operated. However, when the Pleuger is run, the main engine propeller must not be operated simultaneously, which will otherwise cause the Pleuger to be torn away.

Related Reading:

Different types of dry docks for ships

Types of ship’s keel

Voith Propulsion:

You must be wondering why a propulsion system has popped into the discussion when we are interested in rudder systems. Well, that’s something you need to thank the researchers for. Because this propulsion system is one of a kind, which acts as a rudder itself. It doesn’t need a rudder control surface to change the direction of the ship. How? Read on.

As you can see in the figure below, this propeller has a completely different orientation. To visualize it in simple terms, it consists of a number of hydrofoil blades mounted on a disc, which is in turn, mounted onto the hull. The disc rotates in a horizontal plane, about a horizontal axis, and therefore imparts a rotation into the blades.

voith

Image credits: Voith AG, Heidenheim, Germany / wikipedia

But how does a rotation in horizontal plane impart thrust to the ship? Here’s the answer. The blades themselves can be adjusted to have a varying angle of attacks during the operation of the propeller. Depending on that, the direction and magnitude of thrust are varied. Well, if we are manipulating the direction of the thrust too, then we don’t actually need a rudder. Which is actually why a Voith propeller acts as a combined propulsion and steering system for the ship.

It is of no doubt that propulsion and steering systems have been innovated and invented to a great extent when compared to many other aspects in the ship design industry which still require the eyes of modern technological applications. However, as we are transiting into an era of faster, and environmentally safer technologies, newer hull forms are being developed. This has given the industry a wider scope to develop and design newer steering systems for the future.

Related Reading:

Understanding the shipbuilding process

Types of vibrations on ships

Understanding the design of bulk carriers

Leave a Reply

SSCP   CAS-002   9L0-066   350-050   642-999   220-801   74-678   642-732   400-051   ICGB   c2010-652   70-413   101-400   220-902   350-080   210-260   70-246   1Z0-144   3002   AWS-SYSOPS   70-347   PEGACPBA71V1   220-901   70-534   LX0-104   070-461   HP0-S42   1Z0-061   000-105   70-486   70-177   N10-006   500-260   640-692   70-980   CISM   VCP550   70-532   200-101   000-080   PR000041   2V0-621   70-411   352-001   70-480   70-461   ICBB   000-089   70-410   350-029   1Z0-060   2V0-620   210-065   70-463   70-483   CRISC   MB6-703   1z0-808   220-802   ITILFND   1Z0-804   LX0-103   MB2-704   210-060   101   200-310   640-911   200-120   EX300   300-209   1Z0-803   350-001   400-201   9L0-012   70-488   JN0-102   640-916   70-270   100-101   MB5-705   JK0-022   350-060   300-320   1z0-434   350-018   400-101   350-030   000-106   ADM-201   300-135   300-208   EX200   PMP   NSE4   1Z0-051   c2010-657   C_TFIN52_66   300-115   70-417   9A0-385   70-243   300-075   70-487   NS0-157   MB2-707   70-533   CAP   OG0-093   M70-101   300-070   102-400   JN0-360   SY0-401   000-017   300-206   CCA-500   70-412   2V0-621D   70-178   810-403   70-462   OG0-091   1V0-601   200-355   000-104   700-501   70-346   CISSP   300-101   1Y0-201   200-125  , 200-125  , 100-105  , 100-105  , CISM   NS0-157   350-018  , NS0-157   ICBB  , N10-006 test  , 350-050   70-534   70-178   220-802   102-400   000-106   70-411  , 400-101   100-101  , NS0-157   1Z0-803   200-125  , 210-060   400-201   350-050   C_TFIN52_66  , JN0-102  , 200-355   JN0-360   70-411   350-018  , 70-412   350-030   640-916   000-105   100-105  , 70-270  , 70-462   300-070  , 300-070   642-999   101-400   PR000041   200-101  , 350-030   300-070  , 70-270  , 400-051   200-120   70-178   9L0-012   70-487   LX0-103   100-105  ,